Why Is My Weber Grill Not Lighting

Why Is My Weber Grill Not Lighting

Weber Grill Not Lighting | How To Fix A Weber Grill


  • Make sure all the burner control knobs are turned off.
  • Turn the gas supply valve on.
  • Put the match in the match stick holder and strike the match to light it.
  • For current Genesis and Summit models, ignite the remaining burners the same way going from left to right.
  • Steps to Manually Light Your Gas Grill

  • Open the lid of your grill and find the lighting hole on the side of the grill.
  • Once you see that, place a match in the curled end of the holder.
  • Turn on the gas burner closest to the hole.
  • After the first burner is lit, turn on adjacent burners to cross-light them.
  • Propane Or Gas Issues

    Itmight seem obvious, but sometimes the issue has nothing to do with your grillat all. Do you have propane in your tank? If you dont use propane, but insteadhave a direct gas line, check to make sure that its on and that you have gasto the rest of your house. Check to make sure any safety shutoff valves areopen. As always, you should inspect your entire gas line before the start ofthe season.

    Ifeverything seems fine, you should check for a gas leak in your grill itself.

    Todo this, make sure everything is off and cool. When it is, make a solution ofsoapy water and spray it onto your gas lines and connectors. Openthe gas tank, and look for bubbles. If you see any, you know youve got a leak.Make sure to wipe the solution off after youre done testing for leaks.

    Test Your Grills Ignition

    Checkthat all of your igniter electrodes are sparking this might be easy to seedepending on what kind of grill you have. If one isnt sparking, check thewiring for that particular burner. If none are, then check the writing on allof them.

    Ifyou dont find any wiring issues, pull out each electrode and look for anyphysical deformities. Cracks on the ceramic insulators or metal tips could prevent a grill from sparking.

    Ifyou dont find any issues there, youre going to need to grab a multimeter totest the ignition module. Use your meter to check for DC voltage between theelectrode and the burner. With one prong touching each side, press the ignitionand see if you get a reading. If you measure no voltage, youll need to replacethe ignition module.

    Last resort.. use a stick lighter or give us a call to help troubleshoot.

    Read Also: Where Can I Buy Weber Grill Parts

    Burners Produce Orange Or Yellow Flame

  • Remove the control panel to access the Spider Stopper Guards. The control panel is the shelf located above the gas tank. To remove the panel, pull upward on each of the burner control knobs to remove them from the top of the panel, then remove the two screws on the end of the panel with a Phillips head screwdriver. Lift the panel upwards to disconnect it.

  • Locate the Spider Stopper Guards. The Guards are circular metal pieces located at the base of each burner tube, where the tube enters the gas line, and feature several small holes.

  • Inspect and clean the Spider Stopper Guards for signs of dirt or debris. Clean the Guards by brushing them with a soft bristle brush, such as a toothbrush.

  • Position the control panel onto the barbecue, then install the panels two screws with a Phillips head screwdriver.

  • Web Bbq Grill Will Not Light

    Why Is My BBQ Gas Grill Not Lighting Up
    • Check for gas flow by trying to ignite the burners manually using a long-handled match or lighter with the valve open.
    • If you do not get ignition this way, we know that our problem is with the pressure regulator.
    • If all ignited well, then gas flow is not the problem, and it is most likely an issue with the spark igniter.
    • If one or more will ignite but not all of them, it is probable you have a damaged or clogged burner, manifold, or spark igniter.

    You May Like: Which Is The Best Traeger Grill To Buy

    Youre Using The Wrong Type Of Charcoal

    Not all charcoal is made equal. As explained in a previous blog post, there are different types of charcoal, some of which are easier to light and keep lit than others.

    If youre struggling to keep your charcoal lit, you should check to see what type of charcoal you are using. Most charcoal can be classified as either lump or briquette.

    Lump charcoal is the most popular type, as it consists of pure or near-pure carbon. Charcoal briquettes, on the other hand, are comprised of wood and other organic byproducts joined together with a binding agent. While charcoal briquettes typically burn for a longer period of time than lump charcoal, they are also more difficult to light. Therefore, you should stick with lump charcoal if youre concerned about it burning out.

    Check The Pressure Regulator

    The regulator on a gas grill is the part that screws onto the propane tank to regulate the flow of gas. It has a safety mechanism that is called a bypass. This bypass automatically shuts off the gas supply when there is no back pressure in the hose. This can happen if there is a leak. The valve also can also trip if the gas tank is turned on while one of the burners is also turned to the on position. To try and reset this, turn off all burners and the gas tank. Turn on the gas tank and wait a few moments before turning on one of the burners and attempting to ignite it.

    Gas Grill Pressure Regulator May Be Loose Or Faulty

    Recommended Reading: Where Are Memphis Grills Made

    Check For A Faulty Regulator

    A regulator helps bring gas from the tank to the grill, so if there is a fault with the regulator, it can prevent your grill from getting sufficient gas to stay lit. Here are some of the symptoms that indicate a faulty regulator:

    • Low heat coming from the burners even though they arent clogged, or damage could mean that the regulator is the problem.
    • Uneven lighting of the burners.
    • If it takes an excessive amount of time for your grill to get hot it could be due to a bad regulator.

    Grill Light Wont Turn On

    Weber Gas Grill Won’t Light Solutions

    If the lid of your Weber grill is equipped with lights for evening cookouts, it will only activate when the lid is open. Try pressing the AWAKE button once youve lifted the lid. Battery replacement might also be in order.

    Remember that the light will automatically shut off after 30 minutes if theres been no grill activity during that time. You can relight it by pressing the AWAKE button.

    When the light wont shut off, its probably because the lid of the grill is ajar. Make sure to close it completely when youve finished grilling.

    You May Like: What Is The Best Pellet Grill For The Money

    Weber Grill Get Into Bypass Mode

    If you plenty of fuel and clean burners but the heat and wildfires still are not right, then your grill maybe has gone into a big problem called bypass mode. This is mostly happen when the transformer that aluminum contrivance at the end of the gas hose that screws into the tank, then you should detach the gas leakage. Most of the time you open propane container valve. The transformer compares difference strength between gas in the container and the gas in the hose preeminent to the burners. When the preeminent equalize the both incidental side, the transformer grant gas to flow independently to grill when you open one of the burner dominion knobs. To get rid of this nasty problem you can reset the regulator.

    How To Reset The Regulator When In Bypass

    If you think your grill is in bypass mode, you can reset the regulator;by following these steps:

  • Turn off all the burners and close the tank valve.
  • Wait 60 seconds.
  • Open the tank valve fully and wait a few seconds for pressure in the regulator and gas hose to equalize.
  • Open the grill lid, then open one of the burner control knobs and light the grill.
  • Turn all burners to HIGH and close the lid.
  • The flames should be strong and the grill should heat to over 500°F in 10-15 minutes.

    If this process does not work, try it again, but in Step 2 disconnect the regulator from the propane tank and wait 60 seconds before reconnecting it and proceeding to Step 3.

    Also Check: How Do You Grill Baby Back Ribs

    Kinked Or Clogged Hose

    A simple kinked hose can cut off gas to the burners and cause a grill to fail to heat up entirely. Examine the hose and untwist any kinks between the gas line or tank and the burners. Additionally, if you have kept your Weber gas grill outside and unused for a prolonged period of time, you may have clogs in your gas line from spiders’ webs and other debris. Turn off the tank and remove the regulator and hose from the tank and grill. Soak the hose in a solution of soap and water and use a small brush or pipe cleaner to clean as much of the inside of the hose as you can reach. Reassemble the grill and test to ensure the issue is resolved.

    Burners Fail To Light Or Produce Only A Small Flame

    Grill Electric Igniter Not Working. why is my igniter not ...
  • Turn all burner control knobs and the valve on top of the gas tank to the OFF position.

  • Remove the regulator valve from the gas tank. The regulator is the pipe that connects directly to the gas tank. The tip of the regulator valve slides through a metal collar and into the tank. To remove the valve, pull the metal collar towards the gas tank and pull the valve away from the tank.

  • Turn each burner knob to the HIGH position, then allow at least one minute to pass.

  • Turn each burner knob to the OFF position.

  • Reconnect the regulator valve to the gas tank by pulling the metal collar towards the gas tank, then by insert the tip of the regulator valve into the gas tank. Release the collar to secure the valve in place, then turn the valve on top of the gas tank to the ON position.

  • References

    • Weber Spirit 500 Series LP Gas Barbecue Owners Manual; Weber-Stephens Product Co.; 1997

    Writer Bio

    John Stevens has been a writer for various websites since 2008. He holds an Associate of Science in administration of justice from Riverside Community College, a Bachelor of Arts in criminal justice from California State University, San Bernardino, and a Juris Doctor from Whittier Law School. Stevens is a lawyer and licensed real-estate broker.

    Recommended Reading: How To Steak On Grill

    Weber Q Not Lighting All The Way: 3 Fixes

    • Save

    If you are reading this, we are pretty sure that you are a griller and love grilled food. Well, thats why you are using the grills, right? That being said, Weber grills are incredibly famous since they have high-performance features. On the other hand, Weber Q not lighting all the way is disturbing some users. So, lets see how it can be resolved!

    Awful Smell From Weber Grill

    Sometimes most awkward things happen in grill that there is gas smell on grill. Though it is very rears to the Weber grills, if you found that problem you should find the issue. Probably it happen if there is any leakage on gas, spray soapy water throughout the regulator and search for any bubbles. Never grill on weber if you have smelt gas from it. If your grill has a gas leakage and you have smell oily vapor test, and your gas make no inflame turn off your Weber gas, find the issue source. If you get gas smell terminate cooking, urgently get away from the grill and call the fire service for better safety.

    You May Like: Do Weber Grills Come Assembled

    Maybe Youve Got A Gas Leak Or Bad Regulator

    If youre lighting your grill correctly and it keeps going into bypass mode, you may have;a gas leak.;To check for leaks, open the tank valve fully but keep all control knobs in the OFF position. Apply a soapy water solution to the hose and all gas connections using a brush or spray bottle. Bubbles will appear at the point of any leak. Repair any leaks and retest using soapy water to confirm the fix.

    If you cant identify any leaks, then you may have a bad regulator. Contact Weber Customer Service at 800-446-1071 for help.

    Grill Wont Light Start Withpatience

    Why Is My BBQ Gas Grill Not Lighting Up

    Do not get frustrated! One of the first things to go on a grill is the ignition. Most people automatically grab the stick lighter and abandon the ignition all together then try to see what the issue may be.;

    Though, we find, when your grill wont light, theres nothing really wrong. Quite often it can takea try or two to get your grill to light. This is normal and can be for anumber of reasons. While you shouldnt just continuously crank the gas andpound your starter , dont immediately panicif your grill doesnt start.;Usually it is a simple fix.

    Instead,step away from the grill, wait a minute, and try again.

    Dependingon the type of grill you have, you might not be giving your grill enough timeto ignite. Some grills have slower ignition sequences than others, andsometimes the gas takes a few seconds to get through the burner enough to create a spark.;This is especially true with infrared burners. Typically, it takes a longer amount of time for the gas to reach the entire surface area of the burner which means that it takes a few seconds before it will ignite. If you have a center fed tube U Burner, you may want to open the valve and give the gas time to go through the center tube first.

    If theres no gasthere, theres nothing to ignite, which means that youre not going to be ableto start your grill.;

    The most popular ignition systems are:

    Read Also: How Long To Grill Shrimp

    If Your Burner Make Crack Noise

    Sometimes if there got stack spider or any other insects Weber grill maybe make cracking noise. Then you should check your Weber grill if there is any kind of insects remove it. Weber grill sometimes let yellow or orange color for insects problem, then you should be careful about insects. You should proper coverage for insects to saving crack noise. If there any part broken inside then maybe Weber grill burner make some crack noise. If there any part broken out, replace it.

    Regulators On Propane Grills

    If you are using a Weber propane grill and it is not heating up, you may have inadvertently set off the bypass safety mechanism in the gas regulator. The regulator is the silver round or saucer shaped mechanism that sits between the hose and the gas tank. If the regulator detects a leak, it shuts off the supply of gas. You can reset the regulator: turn off the gas at the tank and turn off all of the burners. Turn on the gas at the tank and wait a minute or two for the pressure in the tank and hose to equalize. Then turn on the burners and ignite them as you normally would.

    Also Check: How To Grill Frozen Shrimp

    Tips For Troubleshooting Low Flame Output On Your Bbq Grill

    Posted by Dave | Caring for your BBQ, Featured, Tips & Tricks | 161 |

    Several questions have been asked on my Weber Technical Support Experience blog post regarding low flame output or yellow flame output on your BBQ Grill or burner, so I thought I would post some ideas to resolve the low flame or yellow flame problem. Obviously you have checked the propane tank to make sure that there is fuel in it before resorting to other troubleshooting techniques.

    This post is for the detective in each of us to figure out why the family barbecue is being delayed because the dang hot dogs wont cook. The neighbors are getting impatient, the kids are getting restless and your wife keeps giving you the look like she should have just cooked everything in the kitchen.

    Already Checked The Carryover Tube And Found That It Was Working Properly

    Weber Grill LED Handle Light 7516

    There are also other reasons it could be that only one burner lights. It could be a problem with the gas flow in your grill. Debris in your manifold or valves can block gas from reaching your grill burners. Check for debris around the valves and knobs like built-up grime, dust, or even spider webs. Alternatively, you might need to replace the regulator and hose. Regulators can go bad after time. Theres a safety mechanism that shuts off gas flow so it doesnt create a safety hazard. You can browse available regulator-hose replacements here.

    Recommended Reading: Are Weber Grills Any Good

    Check If The Burner Is Damaged

    If your burners are squeaky clean but still wont work right, it might be because the burners are either damaged or old. Here are a couple of the pointers that indicate that its time to replace your burners:

    • The holes in the burner have become bigger due to being clogged for too long.
    • Excessive flames are coming out of the top or sides of the burner. This could indicate that the burner is damaged.

    Problem: Low Flame Low Temperature

    This is a common problem with many grills and is almost always because of the fuel line regulator . Regulators tend to be sticky. When they stick, they limit the amount of gas and will not generate a good grilling temperature. To reverse this, release the pressure on the regulator to restore normal fuel flow by following these steps:

  • Open the grill lid.
  • Turn all control valves to off.
  • Reconnect the gas line to the tank.
  • Slowly;turn on the gas at the tank.
  • Light the grill.
  • Your grill should now heat normally.
  • To keep the regulator from sticking again, turn off the grill’s control valves first, then turn off the tank valve or natural gas supply line. Always open the tank valve slowly. If this doesn’t work give it a second try. Gently tapping the regulator during step five may help. If you still have a low flame, then you probably have a faulty regulator that will need to be replaced.

    Also Check: How To Grill Hamburgers On Gas Grill

    Popular Articles

    More Recipes Like This