How To Replace Igniter On Weber Grill

Remove Knobs Control Panel Grates & Flavorizer Bars

How to Replace Weber Igniter-Sparker

Pull up firmly on each knob. Theyre held in place by friction, but may resist if they havent been removed in a long time or ever.

On the grill shown here, the control panel is removed by pulling up on the front edge then sliding it out toward you. On other grills, remove the two screws that hold the panel in place, then lift it out.

Now you can see the igniter button, the white ceramic igniter that sticks into the firebox, and the black and white wires connecting the two parts.

Inside the grill, remove the cooking grates and Flavorizer bars. Now you can see the sheet metal gas catcher that houses the ceramic igniter and collects gas for the spark to ignite.

Now is a good time to brush off the burners and punch out any clogged holes with an opened paper clip or small eyeglass screwdriver. These steps are illustrated in my Spring Cleaning post.

Looking under the igniter button, you can see how the black and white wires connect to it. The black wire inserts into the bottom of the igniter button and the white wire slides onto a connector on the side. At the other end, the black wire is connected to the ceramic igniter at the factory and the white wire slides onto a connector on the edge of the gas catcher.

How To Light A Gas Grill With Broken Igniter

Do all grill igniters have a battery?Do not turn the knobs on the grill on just yet.First, raise the lid of your gas grill.Get a bbq match set or a long piece of paper.

Grease, dirt, rain, water, and pieces of food all combine to hinder the strength of your gas grill ignition.How do you light a gas grill if the ignitor is broken?How do you light a gas grill if the ignitor is broken?How to light a charcoal grill with a charcoal chimney.

How to light a gas grill manually.How to light a gas grill manually.I have a bad igniter, is there any way to light a gas furnace manually?my family is cold please help!If it doesnt light, and there are holes in the bottom of your unit, then you can stick a match near the burner from that position.

If it doesnt light, the issue may actually be a clogged or dirty burner.If it doesnt, a new igniter will probably do the trick.If it lights, the problem is likely the igniter.If the burner wont light, first clean and align the electrode.

If the grill fails to light when operated properly, check the burners by lighting manually with a match.If the grill lights with a match, the problem lies in the ignitor.If the grill lights, theres no need to replace the igniter.If the igniter electrode wont spark, first check the ignition module battery and replace it if its dead.

Light your match or paper stick.Make note of how the grill wires enter the starter.Make sure all the burner control knobs are turned off.Make sure all the burner.

Why Is My Bbq Not Igniting

It could be a worn-out spark module, a loose wire or other connection, a dead battery, corrosion or dirt on the igniter tip, or cracked porcelain on the igniter element. If the grill doesnt light using the match, check for low or no gas flow. Your problem could be as simple as a low gas tank.

Recommended Reading: Should The Grill Be Open Or Closed

Genesis Ii Ignition System

    The ignition system to top all ignition systems! Completely redesigned and backed by an industry leading warranty, these igniters are built to last. We increased the warranty from 2 to 10 years! No thats not a typo, these igniters are guaranteed for a decade!

    Our electronic ignition is ensured to ignite every time so you can be confident knowing it will light the first time, every time. Infinity isnt just a clever name, its what we expect from our igniters. From the first light out of the box to the 1000th, the igniter wont let you down!

    Now its time to find out why we increased the warranty by 5 times! There are 4 key elements to our new Infinity ignition:

    1.) Ignition Module:

    We placed the module away from the heat and protected it from the elements. It has been redesigned for even more consistency. The battery compartment has also been relocated for easier access and the battery is a standard AA size so you wont be searching for one of those dreaded disc batteries!

    2.) Wiring:

    With the wires being so close to the heat we beefed them up by giving them a heavy duty coating to improve their heat resistance.

    3.) Electrodes:

    4.) Ignition Switch:

    Genesis II Genesis II offers independent ignition. You turn the control knob to the start/high position and press the igniter button to ignite each burner.

    Genesis II LX Genesis II LX offers a stove like operation. You turn the control knob to the start/high position and it will automatically ignite the burner.

    Remove Replace Install Weber Piezo Module Igniter And Electrode Ignitor

    weber performer replacement gas grill igniter kit 10470 ...

    In older Weber models Genesis, Spirit, Summit the ignition module was a simple mechanical push-button piezo module. These old modules only sparked one time with each physical depression but the never stop functioning unless they are somehow physically broken. Which is highly unlikely in a Weber barbecue grill that mounted the control valves and ignition module on the right side shelf, far from the fire box and any flames.

    The mechanical push button piezo module was also used in extraordinary high end gas grill like DCS and Lynx and was also the module of choice in hundreds of other brands of barbecue grill. No barbecue ignitor module has been more widely used than the Weber piezo ignitor module.

    This instructional video also shows how to replace the electrode and the collector box which is where the ignitor sparks and ignites gas inside the barbecue.

    The smaller tab on the collector box is designed to hold the ground wire. Because the fire box is cast aluminum the electrode is not grounded in the collector box as igniters are in thousands of steel and stainless steel and cast iron fire boxes in other barbecue grill models. The Weber module has a round male plug at the tip for the electrode wire but the module has another male tab that is flat on the side of the module. A wire connects from this side tab to the smaller tab bent on the collector box.

    Instructional Video Shows the installation of the module and the collector box.

    http://www.grill-repair.com

    Don’t Miss: How To Clean Porcelain Grill Grates Char Broil

    Gas Grill Igniter Kit For Genesis #330 Series

    • y_2021, m_11, d_20, h_18
    • loc_en_US, sid_174711, prod, sort_
    • clientName_truevalue

    Online price. In-store price & availability may vary.

    • Works with Weber Genesis 330 grills with front control panel
    • Battery included
    WEBER-STEPHEN PRODUCTS
    California Residents Proposition 65Warning: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov

    How Do You Take Apart A Weber Igniter

    The steps are similar on most older Weber grills:

  • Remove the burner control knobs and control panel to access the igniter parts. Remove the cooking grates and Flavorizer bars to access the gas catcher.
  • Remove and replace the igniter parts and gas catcher.
  • Test the new parts.
  • Put the grill back together.
  • Read Also: What Temp To Grill Chicken

    Example Of Mechanical Igniter Installation

    Im going to demonstrate how I replaced the igniters in my 2002 Summit 450. The steps are similar on most older Weber grills:

    • Remove the burner control knobs and control panel to access the igniter parts. Remove the cooking grates and Flavorizer bars to access the gas catcher.
    • Remove and replace the igniter parts and gas catcher.
    • Test the new parts.
    • Put the grill back together.

    On my Summit, the knobs and control panel are on the front of the grill and there are two igniters to replace:

    On other grills like the popular Genesis 1000, the knobs and control panel are on the right side of the grill and theres only one igniter to replace:

    Thats my 1992 Genesis 2 in the photo above, now being used by my parents. Heres how the igniter is configured on that grill, shown with the control panel removed. This is the same on Genesis 1-5 and 1000-5000 grills.

    Someday Ill photograph the replacement of the igniter in that grill and post them here. Until then, the photos that follow from my Summit igniter replacement will have to do.

    Popular Mechanical Igniter Replacement Kits

    Replace Weber Grill Igniter

    The two most popular mechanical igniter replacement kits are:

    • Weber 7509 Igniter Kit: For Spirit and Genesis , Platinum I and II, Genesis 1000 to 5500, Genesis Silver and Gold , and Genesis Platinum. Does not fit Spirit front-mounted control panel models.
    • Weber 7510 Igniter Kit: For Genesis Silver/Gold/Platinum gas grills and Spirit 200/300 gas grills . Does not fit Genesis Silver/Gold C models after 2003.

    These kits come with an igniter button that generates the high voltage discharge, a ceramic igniter that makes the spark, a black wire and a white wire, a sheet metal gas catcher that collects gas , and installation instructions. The black wire is connected at one end to the ceramic igniter at the factory.

    If you have a grill with a mechanical igniter thats not listed above, call Weber Customer Support at 800-446-1071 to determine the correct igniter for your grill. For example, Ive got a 2002 Weber Summit 450 grill with two mechanical igniters and the replacement part is Weber 901a part that looks identical to the Weber 7509 shown above, but theres some difference between the twoperhaps the wires are a different length.

    Don’t Miss: Traeger Pork Chops

    C430s Choice Series 2burner Freestanding Gas Grill

    Brush the igniter with a stiff toothbrush to remove gunk. Check to make sure they are off by pushing the control knobs in and turning them clockwise until they stop.

    3burner professional 34 grill house styles grilling. Additionally, how do you light a weber gas grill with a match?

    6 outlet aa battery push button electronic ignitor 15v. Also to know is, how do you light a gas grill if electronic ignitor is broken?

    Bbq your way with highquality grilling at an affordable. An electrode wire connecting the ignition to the module delivers the spark to light your gas grill.

    Blaze 4419 natural gas 4 burner professional builtin. An emergency situation would be a situation where your furnace ignitor goes out in the middle of the night, on the weekend.

    Blaze professional 34inch 3burner propane gas grill with. Brush the igniter with a stiff toothbrush to remove gunk.

    Broilmate broilmate 4burner propane gas grill 765264. Check to make sure they are off by pushing the control knobs in and turning them clockwise until they stop.

    Charbroil 463376017 performance 4 burner gas grill 36000. Clean out the gas stove burner holes with a needle.

    Deep cleaning your weber gas grill gas grill clean. Clean the burner and test the igniter again.

    Gas fire pit ignition systems explained gas firepit gas. Clean the gas stove igniter and burner holes if the burner wont light.

    How to replace a broken gas bbq igniter diy projects. Do not turn the knobs on the grill on just yet.

    *** Thanksgiving Recipes ***

    These roasted brussels sprouts get a fair amount of spice from the crushed red pepper flakes, which cuts…

    After trying every turkey-roasting method under the sun, I’ve finally settled on this as absolutely the…

    We love how the cinnamon-scented streusel topping lets the juicy berries peek through.

    Italian sausage and a heap of Parmesan cheese lend signature flair to the easy Thanksgiving dressing…

    It’s all about the layers and ruffles in this dramatic seasonal pie.

    Poach quince in rosé with a dash of cocktail bitters and a few warm spices, then assemble into a tart…

    Leave the sausage, nuts, dried fruit behind in favor of this easy, vegetarian-friendly stuffing recipe…

    Alton Brown’s turkey brine recipe from Good Eats will give you a flavorful Thanksgiving turkey with juicy…

    Bone-in turkey breasts are easy to find, and as impressive as a whole bird when you roast them in butter…

    This recipe was handed down by my great-grandmother. It is a family favorite that we make every Thanksgiving….

    Cutting leeks into large pieces gives them a presence equal…

    This crunchy crumble is the perfect topping for an ice cream sundae, easy apple crumble, or our Build-Your-Own…

    Don’t Miss: Do Traeger Grills Need Electricity

    How To Replace A Gas Grill Igniter

    Nothing beats using a gas grill to make a quick, delicious dinner! However, when the electric igniter no longer works, you may be tempted to throw up your hands and buy a new grill WHOA! Before you go to extremes, Ill show you how easy it is to Replace a Grill Igniter.

    Recently Ive been ordering parts from SearsPartsDirect.com to fix all our broken appliances. When Sears Parts Direct approached me about writing this sponsored post, I naturally replied Yes, of course Id love to share my source for appliance parts! And, I want you all to know my secret for saving money on appliance fixes. With this legal explanation out of the way, let me show you how easy it is to replace that grill igniter that is no longer working.

    Types Of Ignition Systems

    Weber Performer Grill Replacement Igniter Kit 40826404 ...

    Prior to the mid-2000s, Weber used a mechanical piezo ignition system in gas grills. When you depress the ignition button, a spring-loaded hammer hits a crystal, generating a high voltage discharge that travels through wires to a ceramic igniter in the firebox, creating a spark next to the burner tube and lighting the gas. These older systems make a loud metallic bang noise when you depress the rectangular ignition button. Each time you depress the button, a spark is generated.

    Since the mid-2000s, Weber has used a combination of mechanical piezo ignition systems and battery-powered electronic ignition systems in gas grills. The mechanical ignition system is known as Snap-Jet and is integrated into each gas burner control knob. When the knob is turned to the START/HI position, the mechanical igniter generates a spark that lights the gas. The name Snap-Jet is derived from the loud snap noise that occurs when the knob is turned.

    Youll find Snap-Jet igniters on Summit gas grills manufactured from 2003 until time of this writing. On these grills, the igniters are integrated into the gas manifold. If you have a bad igniter, you have to replace the entire gas manifold assembly, a part that costs around $100 at the time of this writing. Not such a great design from a maintenance perspective!

    The Go-Anywhere gas grill uses a mechanical igniter.

    There are a bunch of different versions of these electronic systems, so making sure you buy the right replacement is critical.

    Also Check: Do Weber Natural Gas Grills Have Regulators

    How Do I Light My Weber Grill If Ignitor Is Broken

    Insert the match holder, with lit match, down through the cooking grates, past the Flavorizer Bars and adjacent to the left burner . Push the left control in and turn it to START/HI to igniter the left burner. Check that the flame is lit by looking through the cooking grates. You should see a flame.

    Buying The Correct Igniter Kit Is Key

    Weber has used a variety of igniter kits over the years for different grills. Some kits are mechanical, some are electronic. Some include multiple igniters, some include just one. The wires may be longer in some kits and shorter in others. Its important to get the right kit for your grill because even kits that look alike may not work properly in your specific grill.

    Weber does not list the replacement igniter kit part number in your grills owners manual because these part numbers may change over time. The best way to make sure you get the right kit is to call Weber Customer Support at 800-446-0171. Give them your grills model name and serial number and theyll tell you which part number you need. Alternatively, if youre buying at a home center or online, read the box label or product description carefully to make sure the kit covers your specific grill model and year.

    You May Like: Char Broil Infrared Grill Grates Rust

    How Do I Fix The Igniter On My Gas Stove

    You can fix this problem quickly so that your range passes with flying colors.

  • Access the gas valve behind the stove.
  • Locate the malfunctioning igniter on the stove.
  • Rub a toothbrush across the malfunctioning ignitor to remove any residue.
  • Insert a needle into the ignitors pilot hole, if equipped.
  • How To Replace The Igniter Kit On A Weber Grill

    Replacing your Weber Genesis grill igniter the easy and cheaper way.

    The igniter kit makes lighting your propane grill simple. The kit consists of the igniter module, the wires and electrodes, the push button and battery, and new wire clips. After years of use, the igniter module can wear out no longer producing enough power to make a spark at the electrodes.

    Let’s get started.

    REMOVING THE IGNITER KIT 1. Remove the lid.

    a. Remove the retaining pins from hinge pins at the rear of the lid.

    b. Remove the hinge pins from the hinge brackets.

    c. Lift the lid away from the cookbox.

    2. Remove the grill grates.

    a. Remove warming rack. b. Remove the grill grates.

    c. Remove the flavorizer bars.

    3. Remove the cabinet doors.

    a. Insert a screwdriver into the small opening located on the upper-inside corner of the cabinet door.

    b. Depress the screwdriver to disengage the locking hinge pin and release the cabinet door.

    c. Remove the cabinet door from the grill.

    d. Repeat this step to remove the second cabinet door.

    4. Remove the control panel bottom.

    a. Remove the screws securing the control panel bottom to the upper control panel.

    b. Remove the control panel bottom from the grill.

    5. Remove the ignitor module.

    a. Unscrew the igniter button and remove the battery.

    b. Unscrew the retaining ring securing the igniter module to the front of the control panel.

    c. Push the igniter module out of the control panel .

    d. Disconnect the ignition wires from the igniter module.

    6. Remove the control knobs.

    7. Remove the control panel.

    Also Check: How To Clean Traeger Grill

    Popular Articles

    More Recipes Like This