Using Baking Soda To Clean Up The Grease
One of the ways that you can get rid of grill grease in a quick and timely manner, without leaving a stain behind, is by using baking soda.
This method is pretty simple. All you really need is baking soda, a nylon scrub brush , and dish soap.
First things first, you are going to want to put a thick covering ofbaking soda over the entire stain of grease. You should let this disgustingmixture sit for about 30 minutes while you continue cooking on the grill andmaking sure that there are no other grease stains from the grill grease.
Just before the 30 minutes are up, you are going to want to grab that scrub brush and run it under some water. This is where the dish soap will come in handy, as you drizzle it onto the brush.
From here, you are going to want to scrub the remaining baking soda into the concrete as much as you can with the brush. You should continue scrubbing until all of the grease has been removed.
When all of the grease is gone, you can simply wash down the area with water, and you should let it air dry before you do anything else. Typically, this will get the majority of the grease off your concrete, leaving you with a stainless concrete surface.
If you wait too long, you might end up with mild staining, so keep in mind that time is of the essence.
Follow These Steps To Remove Old Oil Stains From Your Concrete:
If the stain is still present, repeat the process. However, an effective degreaser will remove the superficial layer of the stain after one use. Some commercial degreasers recommend a gradual removal of the stain for optimal results.
Cleaning Grease On The Ground
If youve noticed grease spots on the patio or sidewalk, apply dishwater and boiling water over the area. Use a brush with thick bristles to scrub the area.
Rinse with a hose and keep repeating the process until the grease is gone.
If caught early enough, you can pour baking soda, dry dish detergent, or talcum powder over the affected area. Allow the powder to sit on the stain for half an hour before scrubbing it off with water and a stiff brush.
You May Like: Temps For Pork Chops
Apply The Stripper Solution
- Add paint stripper to an absorbent material to make a creamy paste.
- Note: If you’re working outdoors or in a detached garage and want fast results, you can use a methylene chloride-type stripper. The active ingredient will be listed on the can. But only use this in a well-ventilated area, and wear a respirator equipped with a fresh organic vapor cartridge. If you use a safer, slow-acting stripper, expect to wait several hours for it to work.
- Scrape off the paste and loosened paint with a plastic scraper.
- Let paint residue dry and toss it into the trash.
- Spread a second application if necessary.
How To Remove Tough Stains From Your Asphalt Driveway
Having an Minneapolis MN asphalt driveway gives your property a huge boost in curb appeal. Being one of the many benefits of using asphalt, its ability to make your home beautiful makes it a popular choice.
However, if your asphalt driveway has stains from oil and grease, it can easily become an eyesore. Not only that, big oil and grease stains in your driveway or garage can make its way into your home, potentially ruining your carpet and spreading everywhere else.
Fortunately, while these oil stains can seem impossible to remove, there are ways you can eliminate them using common household products and a little bit of elbow grease.
Lets take a look at these common household products you can use to remove oil stains from your asphalt easily.
Also Check: How To Clean Porcelain Grill Grates Char Broil
Removing An Old Oil Stain
A week or two is enough for oil or grease to settle on your concrete. At this point, you will need a more vigorous approach to treat these. You can distinguish an old stain from a new one by looking at the stains color. Usually, the area with the old oil stain is darker than the other part of your concrete. Some oil also causes blackening when left behind.
A Design Flaw With The Barrel
While not common, some people in this forum have said that continual grease leaks can be due to a design flaw. Pellet grills like other grills are produced in mass quantities, meaning they are prone to some design flaws.
Pit Boss makes a quality product and uses quality control inspectors to examine both materials and products for defects. However, due to the high number of grills they produce, its possible to receive a grill with a flaw such as improper sealant, or etc.
If youre noticing grease leaking from the sides such as by the hopper or by the drip spout, its likely due to a flaw. It likely means that the grill wasnt sealed properly during the production process.
Youll want to contact customer service. Theyll be able to help you determine the cause of the leak and may have to send you a new barrel if the grill is still under warranty.
Also Check: How To Buy Propane Tank For Grills
Removing Grease Using Vinegar
Youve discovered grease on concrete, and you want an easy way to get rid of it. The following solution is pretty simple and requires only a small amount of elbow grease. This homemade concrete cleaner with vinegar is an excellent alternative to commercial cleaning products.
- Scrub brush
Absorb as much oil and grease as you can using sawdust. Mix all of the ingredients into a large bucket. Scoop the solution onto the stain and use the brush to scrub the mixture in well.
Rinse the area thoroughly with water. Repeat the process until the stain is gone.
Soak Up Additional Liquids
If you still have a significant amount of oil or grease on pavers, it is time to deploy the kitty litter. Spread conventional, clay-based kitty litter over the stain. Once you have applied the kitty litter, gently push it into the stain to encourage it to soak up more of the liquids. Do not use a wire brush for this this will scratch your paving stones.
Leave the kitty litter on the oil or grease stain to continue soaking up the liquids. Then remove the cat litter by gently sweeping it up and disposing of it.
Also Check: Clean Char-broil Infrared Grill Grates
Using Heavy Duty Foil
Using heavy-duty foil to wrap the flame broiler can cause the grease to build up and not flow properly. The Pit Boss flame broiler and slide kit are designed to protect meats and other foods from the flame. It is slanted and designed to funnel the grease into the grease trap.
When covered with aluminum foil, it can prevent the flame broiler aka heat shield from operating properly. Some people, wrap the flame broiler in foil to keep it from getting extremely dirty.
If you do wrap the flame broiler, ensure youre wrapping it properly and not leaving any air holes or bulges that can prevent it from working properly.
How To Remove Deep And Old Oil Stains From Concrete Pavers With Cleaning Products
In the event that an oil stain has settled in, or you just want to assure the highest possible level of success when it comes to removing oil stains from your clients pavers, you might need to take more drastic measures. Opting for a professional cleaning solution is your best bet in this scenario.
There are three options here:
Liquid cleaners
Best for: small to medium oil and grease stains on natural stone pavers, brick, grout
Pros: easy to apply, immediate use, great for expensive natural stone cleaning
Keep in mind: smell, manual labor required, less efficient for deep old stains on concrete
Best for: large stains on concrete, asphalt, driveways, pavers, and patios
Pros: Eco-friendly, lowest effort
Best overall: tough and large old stains on pavers, tile, brick, and stone
Pros: low effort, eco-friendly, deep cleaning for the toughest stains
Keep in mind: need to wait at least 8 hours after applying
For deep old stains we recommend:
This product is exceptional at pulling out stubborn grease and oil stains out of pavers. Its a poultice cleaner, meaning all you have to do is spread it out over the stain and wait a certain amount of time for it to work. This oil & grease remover works effectively on brick, tile, block, concrete and stone pavers. Its able to soak up food grease, power-steering fluid, cooking oils, hydraulic fluids, antifreeze and motor oil as well.
Also Check: Which Traeger Grill Should I Buy
Read Also: How Long To Grill Beer Can Chicken
*** Thanksgiving Recipes ***
These roasted brussels sprouts get a fair amount of spice from the crushed red pepper flakes, which cuts…
After trying every turkey-roasting method under the sun, I’ve finally settled on this as absolutely the…
We love how the cinnamon-scented streusel topping lets the juicy berries peek through.
Italian sausage and a heap of Parmesan cheese lend signature flair to the easy Thanksgiving dressing…
It’s all about the layers and ruffles in this dramatic seasonal pie.
Poach quince in rosé with a dash of cocktail bitters and a few warm spices, then assemble into a tart…
Leave the sausage, nuts, dried fruit behind in favor of this easy, vegetarian-friendly stuffing recipe…
Alton Brown’s turkey brine recipe from Good Eats will give you a flavorful Thanksgiving turkey with juicy…
Bone-in turkey breasts are easy to find, and as impressive as a whole bird when you roast them in butter…
This recipe was handed down by my great-grandmother. It is a family favorite that we make every Thanksgiving….
Cutting leeks into large pieces gives them a presence equal…
This crunchy crumble is the perfect topping for an ice cream sundae, easy apple crumble, or our Build-Your-Own…
How To Handle Small Spills
Its easy to ignore a little spilled cooking oil around the backyard grill, but dont let it sit and turn into a stain. Act fast, and keep spilled cooking grease on the concrete off your list of deep-housekeeping projects.
Cover the fresh spill with baking soda, talcum powder or dry dish detergent. Slowly pour liquid laundry detergent over the affected area, and let the mixture sit for half an hour. Pour hot water over the cooking oil spill and concrete. Scrub hard with a stiff brush for several minutes. Rinse with more hot water, and repeat if necessary.
Read Also: Where Can I Buy Bbq Grill Mats
You May Like: Where Is Pit Boss Manufactured
Combat Grease Stains On Concrete Using Baking Soda
The use of baking soda poultice is different from the use of baking soda alone. In this method, you dont need to add water to create a baking soda paste. This technique uses baking soda, which can absorb excess grease and cleanse of the stain it left behind.
Follow these steps to combat grease stains on concrete surfaces with baking soda:
This method does not require any waiting time because scrubbing the stain helps speed up the removal. It is ideal for eliminating fresh grease spills on concrete. However, using baking soda alone will not be enough to remove stubborn old stains.
Warning!
Apply A Makeshift Poultice
Mix some household detergent with baking soda to make a makeshift poultice. Apply the paste to any residual stains. Let the homemade mixture sit overnight. Cover it with durable plastic sheeting. Then, tape it down to prevent children and pets from disturbing it. You can check it after 24 hours. If this method does not work, you may need to employ a more powerful chemical solvent.
Don’t Miss: How To Convert Natural Gas Grill To Propane Weber
How Should I Remove Cooking Oil From Concrete
Last Updated on December 7, 2020 by Diana Rodriguez-Zaba
You accidentally drop a bag of groceries in the driveway. Bottles break, and olive oil quickly soaks into the pavement. Cooking in the backyard is always fun, but it turns into a chore when you spill a gallon of peanut oil on the patio.
These mishaps leave sticky messes that attract dirt and create stains. While home cooking grease spills dont happen very often, theyre easier to handle when you know how to remove cooking oil from concrete.
How To Tackle Large Cooking Oil Spills
Its very hard to clean large areas of concrete soaked with cooking oil. Still, you want to preserve the property value and curb appeal of your home. Different commercial products designed for this type of cleaning include powerful degreasers and microbial cleaners.
Bringing in certified technicians is often more cost-effective than taking on the job as a DIY project, and its safer too. Otherwise, you have to rent the equipment, buy industrial-strength products and round up protective gear. In certain situations, you may also need to report the oil spill to the EPA.
Many homeowners hire a restoration company that specializes in removing cooking grease from concrete parking lots and sidewalks. You want a team experienced with cleaning cooking oil from concrete in commercial settings.
Don’t Miss: Clean Stainless Steel Grates
Grilling On Uneven Surfaces
Grilling on even surfaces or a small slope on the driveway, patio, etc can disrupt the natural flow of the grease in the grill. In addition, grills on slopes or uneven surfaces are prone to tipping over and causing a fire.
Inspect the surface of the patio, driveway, or slab to ensure its flat and even.
If it is uneven or has humps roll the grill to a different place. Set the Pit Boss pellet grill on a stable surface such as a concrete pad so that it remains level while cooking.
How To Remove Grease Stains From Concrete With No Hassle
Concrete is the most common material used for sidewalks, driveways, and patios. As we all park our vehicles in-house, oil or grease stains will inevitably appear on our concrete.
However, it depends on the condition of your vehicle or how much time it has been there on standby. Yet apart from cars, there are countless reasons oil or grease could stain your paver. For instance when during the construction process, oil or grease from several tools or pieces of equipment may readily spill onto them.
Effectively removing and cleaning grease stains from concrete surfaces is essential, whether they’re on the patio of an outdoor kitchen or barbecue grill, on a driveway, or a sidewalk. As a result, these hard surfaces will be easier to keep clean and functional as long as possible.
Some oil stains are minor spills or patches, while others are more highly damaged concrete surfaces. The size and age of the oil stain will indicate how tough it will be to remove. However, using the correct chemicals, you can easily remove grease stains on your concrete surfaces, whether they’re minor or severe, topical or entrenched.
Also Check: How To Cook Grilled Cheese On Stove
Removing Grease Stains Using Baking Soda
Baking soda has so many uses that it comes as no surprise that it is also how to remove grease stains from concrete. It acts as both an absorbent and cleanser. This process is also useful when you need to know how to get rust off concrete.
- Nylon brush
To make an easy cement floor cleaner, apply a thick coating of the baking soda to the stained area of the concrete floor and let sit for approximately 30 minutes. Wet the scrub brush with warm water and apply a few squirts of the soap to the bristles.
Use the soapy brush to scrub the baking soda into the stain until the stain is gone. Give the area a good rinsing and allow it to dry.
How Do You Get Bbq Grease Off Concrete
To get rid of the grease, use baking soda, which naturally draws out the grease residue without harming the concrete.
. Regarding this, how do you remove old grease stains from concrete?
Get those unsightly grease, oil, and transmission fluid stains off your concrete driveway or garage floor. Spray them with oven cleaner. Let it settle for 5-10 minutes, then scrub with a stiff brush and rinse it off with your garden hose at its highest pressure.
One may also ask, how do you remove motor oil from concrete? The four best ways to remove oil stains from concrete are:
Similarly, how do you get BBQ grease off a deck?
For spot cleaning:
Does WD 40 remove oil stains from concrete?
Read Also: Louisiana Grills Vertical Pellet Smoker Vs Pit Boss
